Ethernet cable reference
Ethernet Speed Chart
Twisted-pair Ethernet standards by data rate, with documented category compatibility, per-application channel reach and the conditions attached to each figure.
Ethernet standards and speeds
| Ethernet standard | Link rate | PHY family | IEEE reference | Minimum category |
|---|---|---|---|---|
| 100BASE-TX | 100 Mb/s | BASE-T copper Ethernet | IEEE 802.3u | Cat5e |
| 1000BASE-T | 1 Gb/s | BASE-T copper Ethernet | IEEE 802.3ab | Cat5e |
| 2.5GBASE-T | 2.5 Gb/s | NBASE-T copper Ethernet | IEEE 802.3bz | Cat5e |
| 5GBASE-T | 5 Gb/s | NBASE-T copper Ethernet | IEEE 802.3bz | Cat6 |
| 10GBASE-T | 10 Gb/s | BASE-T copper Ethernet | IEEE 802.3an | Cat6A |
| 25GBASE-T | 25 Gb/s | BASE-T copper Ethernet | IEEE 802.3bq-2016 | Cat8 |
| 40GBASE-T | 40 Gb/s | BASE-T copper Ethernet | IEEE 802.3bq-2016 | Cat8 |
Minimum category is guidance, not a lower bound.A lower category sometimes carries a higher-rate application at reduced reach (2.5GBASE-T over Cat5e, 10GBASE-T over Cat6). The compatibility table below shows which combinations are actually documented, and the conditions attached to each.
Category compatibility and documented reach
Each row shows a documented application-category combination from the reference dataset. An absent entry means no reach is recorded here for that combination — not that the combination is universally impossible.
| Application | Category | Recorded channel reach | Status | Conditions |
|---|---|---|---|---|
| 100BASE-TX | Cat5e | 100 m | Documented | Compliant balanced twisted-pair channel; installation and termination must meet the applicable cabling requirements. |
| 100BASE-TX | Cat6 | 100 m | Backward compatible | Compliant channel. |
| 100BASE-TX | Cat6A | 100 m | Backward compatible | Compliant channel. |
| 100BASE-TX | Cat8 | 100 m | Backward compatible | Lower-rate Ethernet applications are supported over the full structured-cabling channel in the cited Fluke comparison. |
| 1000BASE-T | Cat5e | 100 m | Documented | Compliant four-pair channel. |
| 1000BASE-T | Cat6 | 100 m | Documented | Compliant four-pair channel. |
| 1000BASE-T | Cat6A | 100 m | Backward compatible | Compliant channel. |
| 1000BASE-T | Cat8 | 100 m | Backward compatible | Lower-rate Ethernet application over compliant channel. |
| 2.5GBASE-T | Cat5e | 100 m | Conditional | IEEE/NBASE-T use-case guidance permits operation over installed Cat5e; actual channel performance depends on alien crosstalk, installation, bundling and test results. |
| 2.5GBASE-T | Cat6 | 100 m | With conditions | Installed Cat6 is included in NBASE-T guidance; alien-crosstalk performance can still depend on the channel configuration. |
| 2.5GBASE-T | Cat6A | 100 m | Assured in guidance | CommScope's cited NBASE-T guidance identifies Cat6A as assured across the listed bundled-length ranges. |
| 5GBASE-T | Cat5e | — | Not assured | Do not publish a universal 100 m Cat5e claim. Some installations may work, but this batch does not assign a guaranteed reach. |
| 5GBASE-T | Cat6 | 100 m | Conditional | Installed Cat6 is included in NBASE-T guidance; alien crosstalk/ALSNR and bundling conditions matter. |
| 5GBASE-T | Cat6A | 100 m | Assured in guidance | CommScope's cited NBASE-T guidance identifies Cat6A as assured across the listed bundled-length ranges. |
| 10GBASE-T | Cat5e | — | Not documented | Not listed as a supported cabling category in the cited application guidance. |
| 10GBASE-T | Cat6 | 55 m | Conditional short reach | Reach is installation-dependent; alien crosstalk and field qualification matter. Fluke lists up to 35 m; other guidance commonly gives a conditional range around 37–55 m. Do not present 55 m as universally guaranteed. |
| 10GBASE-T | Cat6A | 100 m | Documented | Full 100 m channel when the complete channel meets Category 6A/Class EA requirements. |
| 10GBASE-T | Cat8 | 100 m | Backward compatible | Fluke's category comparison lists 10GBASE-T and lower-rate applications at the standard 100 m channel distance for Cat8. |
| 25GBASE-T | Cat8 | 30 m | Documented | Short-reach balanced twisted-pair structured cabling channel; use compatible Category 8 / ISO Class I or II components. |
| 40GBASE-T | Cat8 | 30 m | Documented | Short-reach balanced twisted-pair structured cabling channel; use compatible Category 8 / ISO Class I or II components. |
Key application notes
2.5GBASE-T over Cat5e
Installed Cat5e channels may support 2.5GBASE-T under the IEEE 802.3bz NBASE-T use-case guidance. This is not a guarantee for every legacy installation — alien crosstalk, bundling, installation quality and field test results affect whether a specific channel qualifies.
5GBASE-T over Cat5e
The reference data does not establish a universal 100 m Cat5e reach for 5GBASE-T. Do not extrapolate the Cat5e 2.5GBASE-T entry to 5GBASE-T — the two PHYs have different channel requirements.
10GBASE-T over Cat6
Cat6 may support 10GBASE-T over shorter distances, but reach is conditional. The documented range is approximately 37–55 m and depends on alien crosstalk and channel conditions. It is not a guaranteed 55 m figure. Cat6A is the conservative choice for a new 100 m 10GBASE-T installation.
25GBASE-T and 40GBASE-T over Cat8
The documented Cat8 reach is up to 30 m for these specified short-reach applications. The corresponding permanent-link maximum is 24 m. Cat8 is a data-centre short-reach category, not a general 100 m horizontal-cabling recommendation.
Sources
- Network Engineer Tools and Troubleshooting GuideFluke Networks
- ANSI/TIA-568.0-E — Commercial Building Telecommunications Cabling Standard (excerpt)Telecommunications Industry Association (TIA), document hosted by U.S. government procurement source
- Technology Guide: Ethernet Cables and Transceivers OverviewIntel
- Category 6A — The cabling of choice for new installationsCommScope
- IEEE Standard for Ethernet — 802.3bq-2016 overviewIEEE Standards Association
- IEEE P802.3bq draft/comment material containing 25GBASE-T and 40GBASE-T cabling tablesIEEE 802.3