Cat8 Ethernet Cable
Cat8 is classified as Class I (Cat8.1) / Class II (Cat8.2). Documented frequency, channel length, Ethernet application support and construction considerations, with the conditions attached to every figure.
Key specifications
- ISO/IEC class
- Class I (Cat8.1) / Class II (Cat8.2)
- Maximum frequency
- 2000 MHz
- Maximum channel
- 30 m
- Permanent link
- 24 m
- ANSI/TIA recognition
- Recognized
- ISO/IEC recognition
- Recognized
Frequency vs throughput. MHz is a cabling performance parameter, not Ethernet throughput. Channel length includes the permanent link plus patch and equipment cords.
Ethernet speed and distance
The category's baseline application is25GBASE-T / 40GBASE-T at30 m, as represented in the category reference data. Application-specific conditions still apply.
| Ethernet standard | Distance | Type | Status | Conditions |
|---|---|---|---|---|
| 25GBASE-T / 40GBASE-T | 0–30 m | Channel | Class dependent | Short Cat8 channel; TIA Category 8 corresponds to ISO Class I/Cat8.1. Connector class and PHY must match. Permanent link maximum is 24 m. |
Supported Ethernet applications
| Application | Link rate | Recorded reach | Status | Conditions |
|---|---|---|---|---|
| 100BASE-TX | 100 Mb/s | 100 m | Backward compatible | Lower-rate Ethernet applications are supported over the full structured-cabling channel in the cited Fluke comparison. |
| 1000BASE-T | 1 Gb/s | 100 m | Backward compatible | Lower-rate Ethernet application over compliant channel. |
| 10GBASE-T | 10 Gb/s | 100 m | Backward compatible | Fluke's category comparison lists 10GBASE-T and lower-rate applications at the standard 100 m channel distance for Cat8. |
| 25GBASE-T | 25 Gb/s | 30 m | Documented | Short-reach balanced twisted-pair structured cabling channel; use compatible Category 8 / ISO Class I or II components. |
| 40GBASE-T | 40 Gb/s | 30 m | Documented | Short-reach balanced twisted-pair structured cabling channel; use compatible Category 8 / ISO Class I or II components. |
Designed primarily for short data-center links such as switch-to-server connections. The applicable PHY, connector class and complete channel must match.
Construction and connectors
Shielded cabling is required; product designs commonly use 22 AWG S/FTP or equivalent screened constructions.
ISO Class I / Cat8.1 uses the familiar RJ45-style interface; ISO Class II / Cat8.2 uses a non-RJ45 connector system. TIA Category 8 aligns with Class I.
Cable category alone does not specify every construction detail. Check the actual cable datasheet, conductor material, shielding, connector compatibility and installation requirements. See thecable construction reference.
Power over Ethernet considerations
Category designation alone does not guarantee that a cable installation is suitable or safe for every PoE load. The three considerations below are documented in the site's PoE cable guidance dataset — each carries specific conditions that the installer must confirm against the product datasheet and the applicable remote-powering guidance.
Conductor material
Use compliant copper conductors for standards-based PoE cabling; do not assume copper-clad aluminum (CCA) cable is suitable.
Confirm the cable's applicable listing and conductor resistance. Avoid recommending CCA for permanent structured cabling or higher-power PoE.
Thermal conditions
PoE current causes resistive heating in cable conductors. Larger bundles, higher ambient temperature, higher current, smaller conductors and conduit can increase thermal risk.
Bundle size must be evaluated using applicable TIA/ISO/CENELEC remote-powering guidance and the actual cable construction, current, ambient temperature and installation method.
Channel length and power budget
The common structured-cabling channel limit is 100 m, but the usable PD power is affected by channel resistance and power loss.
The 100 m channel length does not guarantee a particular power budget for every cable, connector, temperature or bundle configuration.
See the Power over Ethernet reference for the full standards and guidance, and the product datasheet for conductor AWG, DC resistance and bundling guidance for this specific cable.
Important limitations
Always show 30 m channel / 24 m permanent link and identify the Cat8.1/Class I versus Cat8.2/Class II distinction. Do not market Cat8 as a 100 m 25/40G solution.
The figures on this page describe documented reference conditions. They are not a substitute for testing an installed channel or checking the applicable standards and product documentation.
Related reference
Sources
- ANSI/TIA-568.2-E: Balanced Twisted-Pair Telecommunications Cabling and Components StandardTelecommunications Industry Association (TIA)
- ISO/IEC 11801-1:2017/Amd 1:2025: Information technology — Generic cabling for customer premises — Part 1: General requirementsISO / IEC (JTC 1/SC 25)
- IEEE Std 802.3-2022: IEEE Standard for Ethernet (incorporating 802.3ab, 802.3an, 802.3bq, and 802.3bz)IEEE Standards Association (IEEE 802.3 Working Group)
- Standards Comparison, Version 3.0 / 2024Datwyler IT Infra
- Category 8 Questions AnsweredSiemon / Cabling Installation & Maintenance
- Ethernet Cable Categories Explained: A Brief HistoryFluke Networks
- Network Engineer Tools and Troubleshooting GuideFluke Networks
- ANSI/TIA-568.0-E — Commercial Building Telecommunications Cabling Standard (excerpt)Telecommunications Industry Association (TIA), document hosted by U.S. government procurement source
- Technology Guide: Ethernet Cables and Transceivers OverviewIntel
- IEEE Standard for Ethernet — 802.3bq-2016 overviewIEEE Standards Association
- IEEE P802.3bq draft/comment material containing 25GBASE-T and 40GBASE-T cabling tablesIEEE 802.3