Ethernet Cable Wiring

Pin/pair assignments for T568A and T568B, the difference between straight-through and crossover cables, and the termination practices that determine whether a wired link actually performs.

T568A and T568B pinout

Wire colour names shown as they are normally printed on jacks and plugs. Pin numbers apply to the 8P8C modular connector viewed from the contact side with the latch on the rear.

Pin-by-pin assignment for T568A and T568B. Pins 4–5 (blue pair) and pins 7–8 (brown pair) are identical in both schemes.
PinT568AT568A pairT568BT568B pair
1white-greengreen pairwhite-orangeorange pair
2greengreen pairorangeorange pair
3white-orangeorange pairwhite-greengreen pair
4blueblue pairblueblue pair
5white-blueblue pairwhite-blueblue pair
6orangeorange pairgreengreen pair
7white-brownbrown pairwhite-brownbrown pair
8brownbrown pairbrownbrown pair

Termination schemes

T568A Verified

Eight-position modular connector pin/pair assignment with green pair on pins 1-2 and orange pair on pins 3-6.

Pin order (1 → 8):

  1. white-green
  2. green
  3. white-orange
  4. blue
  5. white-blue
  6. orange
  7. white-brown
  8. brown

T568B Verified

Eight-position modular connector pin/pair assignment with orange pair on pins 1-2 and green pair on pins 3-6.

Pin order (1 → 8):

  1. white-orange
  2. orange
  3. white-green
  4. blue
  5. white-blue
  6. green
  7. white-brown
  8. brown

Cable wiring: straight-through and crossover

Straight-through cable Verified

Both ends use the same termination scheme; pin 1 maps to pin 1, pin 2 to pin 2, and so on.

End A: T568A or T568B

End B: Same as end A

Common use: Common patch-cord wiring; widely used for device-to-switch links.

Caveats:

  • The same scheme must be used at both ends to create a straight-through cable
  • Modern Auto-MDI/MDIX reduces the need to select cable type based on device roles

Crossover cable Verified

For classic 10/100BASE-T crossover wiring, one end is T568A and the other is T568B, swapping the green and orange pairs on pins 1-2 and 3-6.

End A: T568A

End B: T568B

Common use: Legacy direct connection between like MDI/MDI-X interfaces when Auto-MDI/MDIX is unavailable.

Caveats:

  • Many modern interfaces support Auto-MDI/MDIX, making a crossover cable unnecessary
  • Do not assume every device supports Auto-MDI/MDIX; check interface documentation
  • Gigabit Ethernet uses all four pairs; use a standards-compliant cable and verify device support rather than relying on oversimplified legacy diagrams

Termination practices

Practices that affect whether a correctly-schemed cable actually performs. Each practice includes the reason it matters — a visual colour check alone does not prove electrical correctness.

Preserve pair twist as close to the termination point as the connector instructions and cabling standard require.

Excessive untwisting can impair transmission performance and increase crosstalk susceptibility.

Match plug or jack to conductor type, AWG, insulation diameter and cable jacket diameter.

Contacts and strain relief are designed for specified physical dimensions and conductor construction.

Use one wiring scheme consistently across a structured cabling installation; wire both ends of a permanent link according to the selected scheme.

Mixing schemes at the two ends can create crossed pairs or an unintended crossover.

For fixed horizontal solid-conductor cable, use a compatible jack/IDC termination system unless the cable and plug manufacturer explicitly supports direct plug termination.

Structured cabling typically uses permanent-link jacks and separate flexible patch cords; product-specific field plugs are exceptions.

Terminate shielded cable using the exact connector manufacturer's shield and drain-wire instructions, and integrate it with the site's bonding design.

Shield continuity and EMC performance depend on correct cable-to-connector and connector-to-equipment bonding.

Test the completed link for wire map, opens, shorts, reversals, split pairs and category-appropriate performance.

A visual colour check alone does not prove correct pair integrity or transmission performance.

Sources

Published · Last reviewed