Cat6 Ethernet Cable
Cat6 is classified as Class E. Documented frequency, channel length, Ethernet application support and construction considerations, with the conditions attached to every figure.
Key specifications
- ISO/IEC class
- Class E
- Maximum frequency
- 250 MHz
- Maximum channel
- 100 m
- Permanent link
- 90 m
- ANSI/TIA recognition
- Recognized
- ISO/IEC recognition
- Recognized
Frequency vs throughput. MHz is a cabling performance parameter, not Ethernet throughput. Channel length includes the permanent link plus patch and equipment cords.
Ethernet speed and distance
The category's baseline application is1GBASE-T at100 m, as represented in the category reference data. Application-specific conditions still apply.
| Ethernet standard | Distance | Type | Status | Conditions |
|---|---|---|---|---|
| 1000BASE-T | 0–100 m | Channel | Baseline | Compliant Cat6 channel and correctly installed/terminated components. |
| 10GBASE-T | 37–55 m | Channel (estimate) | Field qualification required | Conditional estimate; alien crosstalk, screening, bundle conditions and field test results determine actual reach. Unscreened Cat6 is commonly associated with 55 m; screened solutions may reach farther when requirements are met. |
Supported Ethernet applications
| Application | Link rate | Recorded reach | Status | Conditions |
|---|---|---|---|---|
| 100BASE-TX | 100 Mb/s | 100 m | Backward compatible | Compliant channel. |
| 1000BASE-T | 1 Gb/s | 100 m | Documented | Compliant four-pair channel. |
| 2.5GBASE-T | 2.5 Gb/s | 100 m | With conditions | Installed Cat6 is included in NBASE-T guidance; alien-crosstalk performance can still depend on the channel configuration. |
| 5GBASE-T | 5 Gb/s | 100 m | Conditional | Installed Cat6 is included in NBASE-T guidance; alien crosstalk/ALSNR and bundling conditions matter. |
| 10GBASE-T | 10 Gb/s | 55 m | Conditional short reach | Reach is installation-dependent; alien crosstalk and field qualification matter. Fluke lists up to 35 m; other guidance commonly gives a conditional range around 37–55 m. Do not present 55 m as universally guaranteed. |
10GBASE-T reach is conditional, commonly cited around 37–55 m; actual support depends on alien crosstalk, channel construction and field qualification.
Construction and connectors
Available in U/UTP and shielded constructions; some designs use a pair separator/spline, but that is not a universal category requirement.
Commonly terminated with category-rated 8P8C modular connectors commonly called RJ45.
Cable category alone does not specify every construction detail. Check the actual cable datasheet, conductor material, shielding, connector compatibility and installation requirements. See thecable construction reference.
Power over Ethernet considerations
Category designation alone does not guarantee that a cable installation is suitable or safe for every PoE load. The three considerations below are documented in the site's PoE cable guidance dataset — each carries specific conditions that the installer must confirm against the product datasheet and the applicable remote-powering guidance.
Conductor material
Use compliant copper conductors for standards-based PoE cabling; do not assume copper-clad aluminum (CCA) cable is suitable.
Confirm the cable's applicable listing and conductor resistance. Avoid recommending CCA for permanent structured cabling or higher-power PoE.
Thermal conditions
PoE current causes resistive heating in cable conductors. Larger bundles, higher ambient temperature, higher current, smaller conductors and conduit can increase thermal risk.
Bundle size must be evaluated using applicable TIA/ISO/CENELEC remote-powering guidance and the actual cable construction, current, ambient temperature and installation method.
Channel length and power budget
The common structured-cabling channel limit is 100 m, but the usable PD power is affected by channel resistance and power loss.
The 100 m channel length does not guarantee a particular power budget for every cable, connector, temperature or bundle configuration.
See the Power over Ethernet reference for the full standards and guidance, and the product datasheet for conductor AWG, DC resistance and bundling guidance for this specific cable.
Important limitations
Never present 10 Gb/s over Cat6 as a guaranteed 100 m link. Publish the conditional 37–55 m range with field-test and alien-crosstalk caveats.
The figures on this page describe documented reference conditions. They are not a substitute for testing an installed channel or checking the applicable standards and product documentation.
Related reference
Sources
- ANSI/TIA-568.2-E: Balanced Twisted-Pair Telecommunications Cabling and Components StandardTelecommunications Industry Association (TIA)
- ISO/IEC 11801-1:2017/Amd 1:2025: Information technology — Generic cabling for customer premises — Part 1: General requirementsISO / IEC (JTC 1/SC 25)
- IEEE Std 802.3-2022: IEEE Standard for Ethernet (incorporating 802.3ab, 802.3an, 802.3bq, and 802.3bz)IEEE Standards Association (IEEE 802.3 Working Group)
- TIA TSB-155-A: Guidelines for the Assessment and Mitigation of Installed Category 6 Cabling to Support 10GBASE-TTelecommunications Industry Association (TIA)
- Copper Structured Cabling Design Guide, Issue 10Belden
- Standards Comparison, Version 3.0 / 2024Datwyler IT Infra
- 10 Gigabit Ethernet over Twisted-pair CopperEthernet Alliance
- Network Engineer Tools and Troubleshooting GuideFluke Networks
- ANSI/TIA-568.0-E — Commercial Building Telecommunications Cabling Standard (excerpt)Telecommunications Industry Association (TIA), document hosted by U.S. government procurement source
- Technology Guide: Ethernet Cables and Transceivers OverviewIntel
- Category 6A — The cabling of choice for new installationsCommScope