Cat7A Ethernet Cable
Cat7A is classified as Class FA. Documented frequency, channel length, Ethernet application support and construction considerations, with the conditions attached to every figure.
Key specifications
- ISO/IEC class
- Class FA
- Maximum frequency
- 1000 MHz
- Maximum channel
- 100 m
- Permanent link
- 90 m
- ANSI/TIA recognition
- Not a TIA category
- ISO/IEC recognition
- Recognized
Frequency vs throughput. MHz is a cabling performance parameter, not Ethernet throughput. Channel length includes the permanent link plus patch and equipment cords.
Standards recognition
Cat7A is ISO/IEC Class FA, not an ANSI/TIA category.Cat7A is recognized by ISO/IEC 11801 but not by ANSI/TIA-568. Full channel performance requires an appropriate ISO-compliant connector system — a product sold as "Cat7A RJ45" should not be assumed to deliver the full ISO class without evidence.
Full Class FA performance is associated with ISO-compliant connector systems such as TERA or GG45; RJ45 product claims need exact component/channel qualification.
Ethernet speed and distance
The category's baseline application is10GBASE-T at100 m, as represented in the category reference data. Application-specific conditions still apply.
| Ethernet standard | Distance | Type | Status | Conditions |
|---|---|---|---|---|
| 10GBASE-T | 0–100 m | Channel | ISO Class FA baseline | ISO Class FA compliant shielded channel and appropriate connector system. |
Supported Ethernet applications
No application records are currently available for this category.
Higher specified frequency than Cat7, but does not imply a standardized Ethernet data rate above 10 Gb/s for the common copper Ethernet PHYs covered by this dataset.
Construction and connectors
Shielded Class FA cabling; product implementations commonly use individually screened pairs and an overall screen.
Full Class FA performance is associated with ISO-compliant connector systems such as TERA or GG45; RJ45 product claims need exact component/channel qualification.
Cable category alone does not specify every construction detail. Check the actual cable datasheet, conductor material, shielding, connector compatibility and installation requirements. See thecable construction reference.
Power over Ethernet considerations
Category designation alone does not guarantee that a cable installation is suitable or safe for every PoE load. The three considerations below are documented in the site's PoE cable guidance dataset — each carries specific conditions that the installer must confirm against the product datasheet and the applicable remote-powering guidance.
Conductor material
Use compliant copper conductors for standards-based PoE cabling; do not assume copper-clad aluminum (CCA) cable is suitable.
Confirm the cable's applicable listing and conductor resistance. Avoid recommending CCA for permanent structured cabling or higher-power PoE.
Thermal conditions
PoE current causes resistive heating in cable conductors. Larger bundles, higher ambient temperature, higher current, smaller conductors and conduit can increase thermal risk.
Bundle size must be evaluated using applicable TIA/ISO/CENELEC remote-powering guidance and the actual cable construction, current, ambient temperature and installation method.
Channel length and power budget
The common structured-cabling channel limit is 100 m, but the usable PD power is affected by channel resistance and power loss.
The 100 m channel length does not guarantee a particular power budget for every cable, connector, temperature or bundle configuration.
See the Power over Ethernet reference for the full standards and guidance, and the product datasheet for conductor AWG, DC resistance and bundling guidance for this specific cable.
Important limitations
Clearly separate Class FA's 1000 MHz cabling performance from the Ethernet data rate. Do not claim Cat7A delivers 40 Gb/s Ethernet over 50 m as a general standard capability.
The figures on this page describe documented reference conditions. They are not a substitute for testing an installed channel or checking the applicable standards and product documentation.
Related reference
Sources
- ISO/IEC 11801-1:2017/Amd 1:2025: Information technology — Generic cabling for customer premises — Part 1: General requirementsISO / IEC (JTC 1/SC 25)
- IEEE Std 802.3-2022: IEEE Standard for Ethernet (incorporating 802.3ab, 802.3an, 802.3bq, and 802.3bz)IEEE Standards Association (IEEE 802.3 Working Group)
- What Ever Happened to Category 7?Fluke Networks
- Standards Comparison, Version 3.0 / 2024Datwyler IT Infra
- Category 8 Questions AnsweredSiemon / Cabling Installation & Maintenance